5-15 Strips High Linear Speed Slitting Machine Heavy Load Long
- The tension pad uses high elastics and resistive carpet as surface
materials, so keep the outputs of the Line smoother. In addition,
it also equipped a pressure-balance device to keep an even-pressure
over the both side of materials that toched with the tightener.
- The recoiler is equipped with an improved / high rigid holder, that
causes reduce of lead time a hydraulic pressure adjustable back -
pressure device is equipped on the separator mechanism, so that a
constant hold pressure could be reached for rec oil.
- Self-tension design enables to retain a better tightness during rec
Stainless Steel Slitting Machine introduction
We always choose good suppliers of hydraulic parts, motors, speed
reducers, electric parts. As well, we like to purchase those parts
according to customer requirements for special metal coil slitter.
In the beginning, the coil is loaded on the coil car by crane and
brought to the uncoiler by operating the coil car. Coil car
centralizes the coil with the uncoiler mandrel and the coil is
mounted on the uncoiler. Mandrel is expanded. Snubber roll rotates
the coil. Peeler breaks the straps and brings the pre end upto
Pinch roll. The Pinch roll drives the coil end upto the slitter.
Then its drive is disconnected. Slitter moves the slitted strips
further. Slitted strips are threaded through loop table and drag
tensioner into the recoiler drum. Recoiler winds one turn on loose
Then drag tensioner and loop are put into operation. Slitter and
recoiler run simultaneously in synchronization. As the coil build
up, the recoiler rpm correspondingly goes down to keep desired
constant line speed. This process goes on until the end of coil on
uncoiler. The slitted coil is pushed on the exit coil car through a
pusher plate operated by hydraulic cylinder. The side slitted scrap
is wound on the scrap winder units provided on both sides of the
Matters needing attention in production
1. Be careful not to touch the coil when feeding.
2. Manually adjust the coils on the uncoiler. Normally, the coil
must be aligned to ensure that the width of the two cut edges is as
consistent as possible. In special cases, when there is a large
crack or other defect on the side of the material, the width of the
two cutting edge is not consistent, but the horizontal position of
the coil on the uncoiler must be adjusted manually, and it is
confirmed that the edge defect of the blank can be completely
3. Check the thickness and width of incoming material before
production can be carried out.
4. When the material coil with a thickness of more than 0.5mm is
removed from the steel belt, the roller must be used to prevent the
coil from being thrown.
5. The material should be positive when wearing, and the material
should not be crooked or wrinkled. It is strictly prohibited to
wipe the rollers at the entrance to avoid getting involved.
6. In the process of cutting slitting machine steel , when marks
and scratches caused by the machine are found on the surface of the
plate, the guide rollers on the guide road should be stopped and
checked timely. If any prominent particles are found, they should
be polished with sandpaper and then cleaned with alcohol.
7. Pay close attention to the surface quality of incoming materials
during the operation of the machine. According to the requirements
of the quality and acceptance standard of steel slitting
linemachine, if it is found to be unqualified, it must stop the
machine and find relevant technical quality personnel to deal with
8. Before each roll of material is produced, a sheet of material
should be cut, and the production can be carried out in accordance
with the technological requirements of the length and width on the
card. If not, it is necessary to adjust the parameters of scissors,
otherwise it is not allowed to continue production.
9. When lifting the finished products, it is necessary to carefully
inspect the crane and rigging, and command and operate overhead
travelling cranes to concentrate. Operators are prohibited from
standing in small and unsafe places to prevent material from
10. In case of equipment failure in production, stop immediately
and inform the maintenance staff to deal with it.
RISHBIN, one of the best steel slitting machine manufacturers with
the high-quality steel slitting lines for sale, was founded in
1999. With almost twenty years development, it has become a leading
steel slitting company in this field and exports its quality
slitting machine for steel and other materials to the world.
RISHBIN is dedicated to providing quality services and quality
Stainless Steel Slitting Machine Parameter
|Coil Material||CR Coils , HR Coils, S.S Steel Coils, GI Coils ,AL Coils, Copper
Coils Picking Oil Coils|
|Number of Strip||5～15||8～20||5～15|
|Electrical Control System||PLC Automatic control||PLC Automatic control||PLC Automatic control|